Here

 

 

We've noticed this post involving Installing A Bathtub below on the internet and decided it made perfect sense to discuss it with you on my blog.

Setting up a bathtub isn't exactly rocket science, yet it does need solid plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bathtub with a new one is additionally a reasonably challenging project. If the old bathtub is easily available, the project can relocate easily; if you need to open a wall to get rid of the old bathtub and position the brand-new bath tub, the job is much harder. In either case, the task is within a house handyman's skills, although you will require a helper to move out the old bathtub as well as set in the brand-new one. Make certain you have certified on your own for the job and also fit attempting it. As opposed to employing a professional to take over a halfway-completed task, it is much better to take into consideration utilizing one before you start. Possibilities are you might need a professional plumber to make tube links.
This post will aid you set up a brand-new bath tub in your restroom if you have actually already acquired a new bathtub as well as don't require to change the plan of your previous water supply pipelines.
Your tools as well as material list should consist of the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Measuring tape


• Pipe Caps


 

Planning for the Setup

To start with, the supporting framework supplied with the bath ought to be fitted (if required) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is important to make certain that if the tap includes a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the taps device to avoid pressure on the tub.
Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. See to it you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to now be ready to be suited its last position.

 

 

Removing Old Taps

If you require to change old taps with new ones as a part of your installation, then the first thing you must do is detach the water. After doing so, activate the taps to drain any water remaining in the system. The process of eliminating the existing taps can be rather problematic due to the restricted gain access to that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the faucets. Have a cloth ready for the remaining water that will come from the pipelines. When the supply pipelines have actually been gotten rid of, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from transforming throughout this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any kind of old sealing substance.
Prior to going on to fit the brand-new faucets, contrast the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.

 

 

Mounting the Tub

Utilizing the two wooden boards under its feet, put the bathtub in the called for placement. The wood boards are handy in uniformly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto 4 tiny factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the bathtub till the spirit level reads degree.
To set up taps, fit the bottom of the outermost flexible faucet port to the appropriate supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Activate the water as well as check all joints and also new pipework for leakages as well as tighten them if required. Fill the bath tub as well as likewise check the overflow electrical outlet and also the typical outlet for leakages.
Lastly, repair the bath paneling as defined in the maker's instruction manual. Tiling and also securing around the bathtub needs to wait up until the bathtub has actually been utilized a minimum of once as this will certainly settle it right into its last position.

 

 

Suitable New Taps

If the tails of the new faucets are plastic, then you will certainly require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly need lowering couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin ensuring that the washing machines are in location between the faucet and the sink. Protect the tap in position with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The former kind needs to be connected to the tap finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.

 

 

Tiling Around the Bath tub

In the area where the bath fulfills the tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to break a stiff seal, creating the water to penetrate the wall between the bathroom and also the tiling, leading to problems with moisture as well as feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your components and also fittings. They are offered in tubes and also cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of drenched paper or soft rope. Remember to always fill up the tub with water prior to securing, to allow for the movement experienced when the tub remains in usage. The sealer can crack fairly early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof glue and also cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I was made aware of that editorial on How to Install a Bathtub Yourself through an associate on another web address. Are you aware of somebody who is intrigued by How to Install a Bathtub? Take a moment to share it. Thank you for your time. Come back soon.

Estimate Free

Information

 

They are making several good points regarding Know When to Replace a Toilet as a whole in this great article just below.

Plumbing issues at home don’t get worse than a faulty toilet. Faulty or poorly functioning toilets are a nightmare to house owners. Imagine doing your business in the bathroom, and the toilet won’t flush. It becomes embarrassing if it’s a shared toilet and someone else needs to use it. In other cases, no matter how much you flush, the water seems incapable of washing the whole thing away.
There are numerous signs that your toilet might be faulty, and we will briefly look at these signs and occurrences that, when noticed, you need to contact a professional plumbing service to either fix the toilet or reinstall it.

 

1. Clogs

Clogging toilets happen pretty regularly, and everyone experiences it once in a while. But if your toilet stops more frequently, you may need to have it checked. If you have kids at home, the chances are high that they may have tried flushing toys or fabrics down the drain at some point. A clogged toilet poses a significant threat to the sewage, especially when materials other than tissue papers and human waste are flushed down there. While a plunger can do most of the unclogging, you should call a professional if you notice that it happens very frequently. Your toilet might need more than just a plunging to get back in good shape.

 

2. Crack in the Tank

The first sign that your Tank may be cracked is the presence of water puddles near the base of your toilet. Cracks in the Tank are sometimes hard to detect, especially if it’s just a tiny one somewhere below the waterline. When you notice water settling on your toilet base, it is most probably indicative that your Tank has cracked, and you need to involve the plumbers to detect the spot and either fix it or replace it.

 

3. Leaky Toilet

Sadly, the only way you may realize you have a leaky toilet is when the water bills keep going up. Leaky toilets are terrible because they can cause lots of damage in the home, including creating a room for molds and mildews, ruining the flooring, and if the faulty toilet is in an upstairs bathroom, it can cause problems to spaces beneath it. The best solution for a leaky toilet, especially if it’s old, is to replace it. Contact a professional to take a look at it and let them do the job.

 

4. Weak Flush

If your toilet does not let a lot of water down to flush everything, there might be a problem. Ideally, one flush should be enough to send all your wastage down the sewers. Having to flush your toilet more than once or twice is tiring and affects the bills. It is a sign of a blocked pipe or a faulty flushing mechanism. In some cases, the water in the toilet bowl is constantly running, and there is not enough to flush when you need to. Only a professional can detect if it’s a flapper valve problem or something else.

 

Effects of Faulty Toilets

Faulty toilets can hamper your health and cause an increase in utility bills. They can create room for molds, bacteria, and other unpleasant organisms to lurk in the bathroom. Faulty toilets can also increase the risk of flooding and clogging. Ironically, some of these signs are hard to detect or trace, and in many cases, you will require a professional to detect and fix them.
Toilets don’t last forever, and like every other thing, they can outlive their purposes and require a replacement. There are some signs and symptoms that accompany a faulty toilet, and your ability to take note of them on time and call in professionals can save you a lot of risks.

 

Let the Pros In

These are some of the most common causes of a faulty toilet, and now that you know, you certainly have an idea why there is always water at the base of your toilet or why it does not flush properly.
When you notice these signs, quickly contact a professional. If you live in Pittsburgh, our experienced plumbers can help salvage your toilet and get it back in good working conditions.
Some of these faults are indicative of a need to replace your toilet. We also handle toilet installations and replacements. With our many years of experience in the field, our services are unbeatable.

 

7 Common Causes of Toilet Plumbing Problems

 

Clogs

 

Almost everyone has encountered a clogged toilet! They’re annoying, but they can also be damaging. Unchecked clogs can cause issues to your plumbing and home, such as mold or warped flooring.

Some clogging issues are caused by flushing foreign objects down the drain. These can pose serious problems for your sewer system, creating severe backups. Besides human waste, the only items you should flush are soft paper products like toilet paper and thin napkins. While other paper products may seem like they go down just fine, they can become stuck or build up in the pipes. If you have children in your home, be careful that they don’t flush toys, fabric, or food down the drain. Your toilet’s well-being depends on it!

 

Worn Flapper Valve

 

Worn-out and malfunctioning toilet parts are another common cause of toilet problems. A flapper is the piece of your toilet that allows water to move from the cistern into the toilet bowl and fill up the bowl after the toilet is flushed. A deteriorated flapper valve can cause your toilet to flush on its own or to run constantly, which could make your water bill skyrocket.

 

Worn Washer Bolts

 

If you keep finding random puddles of water under the toilet tank, there are a couple of likely explanations. One is worn washer bolts.

Step one: Take a look at the bolts in the toilet, and feel the outside and bottom of the tank for a leak. There may be a leaking bolt washer that just needs to be tightened.

 

Loose Connections

 

Loose connections are another cause of a leaking toilet. It’s normal for pieces to fall out of place over time, even on toilets. Rubber linings, for example, can wear away, allowing water to seep through.

Mounting nuts and supply tubes may also loosen up. You’ll want your plumber to go over these areas to ensure everything is sealed properly.

 

Condensation

 

Condensation is another toilet problem that could lead to you finding water on your bathroom floor. A poorly insulated tank might be the cause of the condensation, thanks to cold air. If this is the case, call a professional to come over and cover the impacted areas of your toilet with insulating liners.

https://www.cwservicepros.com/toilets/toilet-problems/

 

Do you really like reading up on Know When to Replace a Toilet? Write a remark down below. We'd be interested to see your thoughts about this blog entry. In hopes that you come back again later on. Sharing is caring. You won't know, you may be doing someone a favor. Thank you for your time. Please pay a visit to our site back soon.

Dial, and relax!